What is corrosion of steel?
Corrosion of steel is an important phenomenon that need to be understood properly. According to ASTM, corrosion is “the chemical or electrochemical reaction between a material, usually a metal, and its environment that produces a deterioration of the material and its properties.” In reinforced concrete, corrosion cause formation of rust around the steel bars which is as big as two to four times the original volume of steel. Corrosion also produces holes in the surface of steel in embedded concrete due to which cross sectional area of steel is reduced which in turns reduces structural strength of the steel.
Why is corrosion of steel a concern?
Concrete is weak in tension and strong in compression and steel is good in tension. To enhance tensile properties of the structure, steel is used along with the concrete which makes it reinforced concrete. Reinforced concrete is used in structures which are subjected to tensile and flexural stresses. These stresses come from structural loads, live and dead loads, traffic, winds and earthquakes etcetera. Corrosion of steel results in loose bonding between concrete and steel which in turn results in spalling of concrete. This makes structure weak and unsafe. Corrosion also produces holes in the surface of steel in embedded concrete due to which cross sectional area of steel is reduced which in turns reduces structural strength of the steel.
Why does steel in concrete corrode?
The corrosion of steel in concrete is an electrochemical process which requires presence of moisture, oxygen and some catalyst to start electrochemical process. In this process, iron in the steel is oxidized to produce rust, which can be as big as two to four times the original volume of steel. Steel when casted in concrete is in passive condition. Sometimes concrete structure is exposed to such environmental conditions which makes chlorides absorb in concrete. These chlorides penetrate the concrete and reaches the structural steel. This provides a favorable environment for process of corrosion to start. This process can also be started due to carbonation of concrete. However rate of corrosion in carbonated concrete is slow as compared to corrosion due to chloride.
How to prevent corrosion?
Increasing concrete quality
Corrosion of steel can be prevented by producing good quality of concrete and by providing appropriate concrete cover around reinforcing steel bars. Quality concrete can be produced by keeping water to cement ratio as low as possible. This will prevent chloride penetration and carbonization of concrete. To avoid penetration of chloride into concrete, water to cement ratio should be less than 0.4. And to avoid carbonization of concrete, water to cement ratio should be less than 0.5. Water to cement ratio can be reduced by increasing cement content or by reducing water content by using water reducer admixtures or super plasticizers.
Quality of concrete can also be enhanced by air entertainment through air entertaining admixtures. Air entertaining admixtures introduce very tiny air bubbles in concrete also called air entertained bubbles. These air bubbles increase the concrete’s resistance to damage caused by freezing and thawing. Air entertainment also reduces segregation and bleeding of concrete and thus permeability is also reduced as concrete has no bleed channels.
Minimizing cracks, spalling and scaling of concrete
Cracks in concrete is another reason of corrosion of steel. Cracks along with spalling and scaling of concrete can accelerate corrosion process of reinforcing steel bars. Cracks, spalling and scaling of concrete can be reduced by properly execute finishing operations of fresh concrete. Cracks can also be minimized by providing correct amount of steel. Reinforced concrete should be properly designed as per guidelines of ACI standards to minimize cracking. As per ACI, maximum allowable crack width to avoid corrosion is between 0.006 inch and 0.007 inch depending upon environment in which concrete is to be used.
Providing adequate concrete cover
Proper concrete cover plays very important role in controlling corrosion. Chloride penetration and carbonization cannot be stopped even in low preamble concrete. However these processes can be delayed by increasing concrete cover. In general, chloride will penetrate 4 times slower in 2 inch concrete cover as compared to 1 inch concrete cover. ACI 318 gives recommendation for concrete cover to be 1.5 inch for most of the structures. Concrete cover increases up to 2.5 inch depending on environmental conditions which are more liable for chloride ionization or carbonization of the concrete. Concrete cover also depends on size of aggregates. Larger aggregates in concrete require increased covers. As a rule of thumb, if aggregate size is greater than ¾ inch, add ¾ inch to maximum aggregate size to have minimum concrete cover to be used in deicing salt exposure. And if aggregate size is greater than ¾ inch, add 1-¾ inch to maximum aggregate size to have minimum concrete cover to be used in marine environments. For example, concrete with 1 inch aggregate in a deicing salt exposure should have a 1-3/4 inch minimum cover and if same is to be used in marine environment than cover should be minimum 2-3/4 inch.
Consolidation and curing of concrete
The concrete must be consolidated and cured properly. Concrete with water to cement ratio of 0.40 should be cured for at least 7 days at 70°F (21 °C). Increased water to cement rations increases required curing time. For example concrete with water to cement ratio of 0.60 should be cured for at least six months to have same performance as that of 7 days curing for 0.4 w/c concrete. Increased curing times reduce porosity of concrete which will in turn reduce corrosion of the structural steel embedded in concrete.
Modified Concretes and Corrosion Protection Systems
Corrosion can also be reduced by adding corrosion resistant additives to concrete. These additives include silica fume, fly ash and blast furnace slag which reduces permeability of the concrete. Water repellents can also reduce the entry of chlorides and moisture to a limited extent.
There are some other corrosion protection techniques which include protective membranes around steel bars, epoxy-coated reinforcing bars, cathodic protection and concrete sealers (if reapplied every four to five years).
CONCLUSION
To avoid corrosion of steel in concrete:
- Use good quality concrete. Which can be produced by air entertaining with a water to cement ratio of 0.40 or less.
- Use concrete cover of 1.5 inches as minimum and at least ¾ inch larger than the nominal maximum size of the coarse aggregate used in concrete.
- Increase the minimum cover of concrete to 2 inches for deicing salt exposure and to 2.5 inches for marine environment.
- Ensure that the concrete is consolidated and cured properly.
- Use corrosion resistant additives like fly ash, silica fume and blast-furnace slag.
Share this post with your friends generously and do comment. This will motivate me to share more cool stuff with you 
- Essential Software Tools for Planning Engineers in the Construction Industry - May 22, 2023
- PMI Certifications for Planning Engineers - May 22, 2023
- 10 Basic Interview Questions for a Planning Engineer - May 22, 2023
- Work Break Down Structure & its Importance - September 5, 2018
- Corrosion of Steel in Concrete - March 14, 2017
TMT Rebars are highly recommended to use for weld joints without any strength reduction due to having less carbon in it.
TMT bar suppliers in Tamilnadu
Very well written blog post, the points mentioned here are really appreciated.
We are a wholesale supplier of steel products from Kolkata, West Bengal. We supply branded products such as SAIL, VIZAG, JINDAL PANTHER. To name a few products, we have tmt bars, angles, channels, beam, flat, round, square bars, etc. To know about us check our website https://shreejisteelcorp.com/
this is an informative post and it is very useful and knowledgeable. therefore, I would like to thank you for the efforts you have made in writing this article.
We have a construction company:https://www.sscorporation.com.bd/
Nice blog thanks for sharing. This is very nice information, thanks for sharing this valuable information. We deliver the best TMT bars all around India. We manufacture the best steel TMT bar from the best quality of steel from the fresh factory methods, which is Long lasting over generations. We use a unique manufacture technique for the TMT bars. We are available from all the construction TMT bar dealers, suppliers & manufacturers. For more details visit our website https://isteel.in/
MqwjVD Would you be interested by exchanging hyperlinks?
Thanks for the informative post, TMT bar Dealers in Tamilnadu.iSTEEL is one of the best high-quality TMT bar manufacturers, TMT dealers, and TMT suppliers in Chennai, Tamilnadu. TMT bar you can trust blindly because of its super strong and corrosion resistance TMT bar. For more visit https://isteel.in/
If you are going for best contents like myself, only pay a quick visit this website all the time as it gives
quality contents, thanks
An intriguing discussion is worth comment.
There’s no doubt that that you need to write more about this topic, it may not be a taboo matter but usually people do not talk about such topics.
To the next! All the best!!
What’s up to all, the contents present at this site are in fact amazing for people knowledge, well, keep up the nice work
fellows.
You may desire to place a little towel below your feet throughout the massage to avoid spilling the
oil on to your clothes or bedding. Now you will massage your ears; start top of your ears, then massage hard all way on the ear.
The opening and expanding of bloodstream assist in keeping the follicles widened.
The therapist will need to have advanced training and experience in treating
soft tissue injuries. With the help of these oils, you feel more
relax after a massage. Individuals looking to become a certified massage therapist will likely need to finish a thorough educational training program.
This content is so good thanks for sharing!!!
https://sealingandcorrosion.co.uk/